Same-day diagnostics and board replacement done right the first time
Gas Dryer Control Board Repair Saratoga CA You Can Count On
Gas Dryer Control Board Repair Saratoga CA is what we do every day, and we do it fast. If your Whirlpool, LG, or Samsung dryer has gone dead, flashing error codes, or heating in bursts, the board is usually the culprit. We test the board, the thermal fuse, and the gas valve before we quote a thing, so you know exactly what you are paying for. Most Saratoga jobs are finished the same day we arrive.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Control Board Repair Includes
Every Gas Dryer Control Board Repair Saratoga CA job includes a full diagnostic, the board repair or replacement, and a system test before we leave. Here is what is covered in a standard visit, and what we treat as an add-on if we find it.
Full Diagnostic Test
We test the control board, thermal fuse, igniter, flame sensor, gas valve, and door switch with a multimeter and manometer. You get a written diagnosis and a price before any repair starts. The diagnostic fee is waived when you approve the repair.
Board Repair or Replacement
If the fault is a repairable relay or solder joint, we fix it on the bench and save you the cost of a new board. If the board is fried, we install a new control board matched to your exact model number. Both options carry a warranty.
Gas Line Safety Check
We shut the gas valve, inspect the gas line connector, and check every fitting with a gas leak detector before and after the repair. If we find a leak, we repair it and pressure-test the line. Gas safety is not optional on our jobs.
Vent and Airflow Inspection
A clogged vent is the leading cause of control board failure. We check the lint trap, vent hose, and exterior flap, then clear any blockage we find. Good airflow keeps your new board running cool and extends its life.
Full Cycle Test
Before we leave, we run the dryer through a complete cycle. We watch the igniter glow, confirm the flame sensor reads correctly, and check that the drum turns smoothly. You see the dryer heat up with your own eyes.
Cleanup and Warranty
We vacuum the lint trap housing, wipe down the cabinet, and put the dryer back in place. You get a written warranty on the board and our labor, plus a maintenance tip sheet. If the same fault returns inside the warranty window, we come back free.
Service overview
Gas Dryer Control Board Repair Saratoga CA Explained
Gas Dryer Control Board Repair Saratoga CA is the diagnostic and repair work that restores the logic board controlling your dryer's motor, igniter, gas valve, and timer. The board is the brain of the machine. When it fails, you get a dryer that will not start, will not heat, or runs for two minutes and quits. We pull the board, test every relay and solder joint with a multimeter, and either repair the fault or swap in a new control board matched to your model number.
Saratoga homes run gas dryers hard, and the symptoms show up fast. You might get a dryer that tumbles cold, a drum that will not turn, or a unit that trips the breaker every cycle. We see plenty of gas dryer control board troubleshooting Saratoga calls where the real problem is a blown thermal fuse or a clogged dryer vent cooking the board. We check the whole circuit, not just the part you called about, so the fix actually holds.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How Our Control Board Repair Process Works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone Triage
We ask for your dryer brand, model number, and the symptom: no heat, no start, no spin, or error code. That five-minute call lets us load the right control board and tools in the truck. If it sounds like a gas leak, we treat it as an emergency and roll immediately.
On-Site Diagnosis
Our tech pulls the dryer out, unplugs it, and shuts the gas valve. We test the control board, thermal fuse, igniter, and door switch with a multimeter, then check the vent with a thermal imaging camera. You get a written diagnosis and a price before we touch a screw.
Board Repair or Replacement
If the fault is a repairable relay or solder joint, we fix it on the bench. If the board is fried, we install a new control board matched to your model. The swap takes 30 to 60 minutes on most Whirlpool, LG, and Samsung units. We photograph the old board and show you the failure point.
Full System Test
We reconnect the gas line, check every connection with a gas leak detector, and run the dryer through a full cycle. We watch the igniter glow, confirm the flame sensor reads correctly, and check that the drum turns smoothly. You see the dryer heat up before we call the job done.
Cleanup and Warranty
We vacuum out the lint trap housing, clear the vent hose, and wipe down the cabinet. You get a written warranty on the board and our labor, plus a maintenance tip sheet. If the same fault comes back inside the warranty window, we come back at no charge.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Multimeter
Tests voltage, continuity, and resistance on the control board, thermal fuse, igniter, and door switch. It is how we confirm a failed component instead of guessing.
Manometer
Measures gas pressure at the valve to confirm the burner is getting the correct supply. A weak gas valve or low pressure shows up here first.
Gas Leak Detector
Sniffs every fitting on the gas line connector and valve before and after the repair. We never leave a job without a clean reading.
Thermal Imaging Camera
Finds hot spots on the control board and along the vent run. Overheating is the number one killer of control boards, and this camera shows it instantly.
Nut Drivers and Screwdrivers
Standard hand tools for pulling the cabinet, control panel, and board. We use magnetic-tip drivers so screws do not end up inside the drum.
Vent Brush and Vacuum
Clears lint from the trap housing and vent hose. Good airflow keeps the new control board running cool and protects the thermal fuse.
Use cases
When Saratoga Homeowners Call Us
These examples show how the service framework adapts rather than forcing every call through one repair.
Maytag No-Heat Fixed Same Day
A Maytag gas dryer in Quito Village tumbled but never heated. The igniter glowed, but the burner never lit. Testing showed a weak gas valve coil and a control board that was not sending full voltage to the valve. → We replaced the gas valve and repaired the control board relay on the bench. The burner lit within 30 seconds of the cycle start, and the flame sensor read correctly. The homeowner saved the cost of a new board.
Kenmore Error Code Cleared
A 12-year-old Kenmore gas dryer in Saratoga Village flashed an error code and quit after two minutes. The homeowner was ready to buy a new dryer. The control board had heat damage, and the vent was clogged with years of lint. → We replaced the control board, cleared the vent run, and replaced the thermal fuse. The dryer ran a full 60-minute cycle with no error code. The repair cost a fraction of a new dryer.
Problems we solve
Control Board Problems We Solve in Saratoga
A failing control board shows up in a handful of ways. Here are the ones we see most in Saratoga, what happens if you ignore them, and how we fix them.
Gas dryer will not start at all
We test the board, door switch, and thermal fuse to isolate the failure. If the board is dead, we install a new control board matched to your model, usually the same day. You get a full cycle test before we leave.
Dryer tumbles but will not heat
We test the igniter, flame sensor, and gas valve with a multimeter and manometer, then check the control board output. We replace the failed part and confirm the burner lights before we call it done.
Dryer runs a few minutes then quits
We clear the vent run, replace the thermal fuse if blown, and test the control board for heat damage. Fixing the airflow is the key to stopping the cycle from repeating.
Error code flashing on the display
We read the code, then test the exact circuit it points to: board, sensor, or valve. You get a clear diagnosis and a repair that targets the real fault, not a parts shotgun.
Pricing process
Control Board Repair Pricing in Saratoga
$220 - $650 depending on board type, additional parts, and vent condition
Board Type and Brand
Control boards for Whirlpool, Maytag, and Kenmore are usually less expensive than LG, Samsung, and Bosch boards. Electronic boards with digital displays cost more than basic models. We quote the exact board price for your model before ordering.
Repair vs. Replacement
If the fault is a repairable relay or solder joint, we fix it on the bench and save you $100 or more. If the board is fried, replacement is the only safe option. We tell you which one you need, honestly.
Additional Failed Parts
A control board often fails alongside a thermal fuse, igniter, or gas valve. Replacing those parts adds $40 to $150 to the job. We test everything first so you only pay for what has actually failed.
Customer reviews
What Saratoga Customers Say
★★★★★
“Our LG gas dryer went completely dead on a Friday. Gas Dryer Repair Pros came out the same afternoon, tested the board and thermal fuse, and had a new control board in by 4 p.m. The tech showed me the burnt spot on the old board. Fair price, no upsell, and the dryer has run perfectly since.”
★★★★★
“I called three places and nobody could come for a week. These guys answered on the second ring and were at my house in two hours. The control board was fine, it was a clogged vent cooking the thermal fuse. They cleaned the vent, replaced the fuse, and charged me less than the quote. Honest work.”
★★★★★
“Our Maytag dryer was flashing an error code and would not heat. The technician diagnosed a failed control board relay, repaired it on the bench, and saved us the cost of a new board. He also checked the gas valve and igniter while he was in there. Fast, clean, and he explained everything.”
How much does gas dryer control board repair cost in Saratoga CA?
Most gas dryer control board repair in Saratoga CA runs $220 to $480 in 2026, including the diagnostic, the board, and labor. Simple relay repairs can land near $180, while a board plus thermal fuse and igniter replacement pushes toward $500. We give you a written range before we start, so the number does not move.
Who repairs gas dryer control boards near me in Saratoga?
We do. Gas Dryer Repair Pros is a licensed gas appliance repair company serving Saratoga, CA and all of Santa Clara County. Our techs carry control boards for Whirlpool, Maytag, LG, Samsung, GE, Kenmore, and more. Call +16693329106 and we will schedule a same-day or next-day visit, depending on the time you call.
Can a gas dryer control board be replaced same day in Saratoga California?
Yes, in most cases. If your dryer is a common Whirlpool, Maytag, LG, Samsung, GE, or Kenmore model, we likely have the board on the truck. Same-day gas dryer control board repair Saratoga CA is our standard for calls before 2 p.m. Special-order boards take two to five business days, and we tell you upfront.
How do I reset my gas dryer control board in Saratoga?
Unplug the dryer or flip the breaker for 60 seconds, then plug it back in and press and hold the start or power button for five seconds. That clears most soft faults. If the board still will not respond, or you smell gas, stop and call us at +16693329106. A board that will not reset usually needs replacement.
Related services
Related Services
Gas Dryer Repair
General gas dryer repair covers the full machine, including the control board, motor, and drum. If you are not sure the board is the problem, start here. We diagnose the whole unit and fix what is actually broken.
Gas Dryer Not Heating Repair
A dryer that tumbles cold often points to the igniter, flame sensor, or gas valve, not the board. We test all three plus the control board so you are not replacing the wrong part. Most no-heat calls are fixed in one visit.
Gas Dryer Not Spinning Repair
When the drum will not turn, the drive belt, motor, or door switch is usually at fault. A failing control board can also stop the motor signal. We test the full circuit and replace only what has failed.Ready when you are
Get Your Gas Dryer Control Board Repair Saratoga CA Today
Licensed, insured, and warrantied on every board we install. Call +16693329106 and we will schedule a same-day visit, or an emergency call if your dryer is dead and you need it back now. Upfront pricing before we start.
Talk with the local team
Request Gas Dryer Control Board Repair
Call us at +16693329106 or email info@gasdryerrepairpros.com. We answer calls 24/7 for emergencies and schedule same-day service Monday through Saturday. Our office is in Saratoga, and we serve the whole Santa Clara County area.